odowdpat, It most likely is the charge pump circuit. Does the out-4 LED come on. Out-4 needs to come on if you are using the XML file from my web page. You...
Anybody interested in a tool changer for a full size knee mill (NMTB 40), please contact me offline at the address in the header for this message. Thanks Rod...
Well the question for the New Year, is who is going to be the first to make one of these (or one like it) as a part of a CNC system? Or the CNC system?? ...
this might be a little late now -but: The ROD 450 is a current sin wave device It has a line count from 50 to 5000 (will say on the name plate) 12000 max rpm...
Hi Randy, Some ideas at www.5bears.com, and also my own website www.gimbal.com.au - look for the CNC mill links on both these sites. Cheers, Pat ... From:...
bill, parts express has them, best part is the receptacles use .187 fastons and the plugs use screws, makes it easy to hook up. Be sure to use good quality...
Bob, Thank you for your reply. It was the jumper. I manageed to get the X & Y axis moving, again thank you. Patrick ... on. ... page. ... Setting it to ... X ...
because drivers can be loaded and unloaded at will, linux is really always running in "safe mode" perhaps you mean single mode any linux sys should run in this...
... I think Paul Corner has been doing it for years. I'm pretty sure he had a compact PCI system at the EMC codefest in Gaithersburg, MD last April. Jon...
... Actually, there are just two system programs (insmod and rmmod) that need to be installed with the system priveledge bit set. Newer BDI distributions have...
This list is for the discussion of CNC and related topics including CAD, CAM, EDM, & DRO. The list focuses on the construction of home shop CNC machines along...
CAD_CAM_EDM_DRO@yahoo...
Jan 2, 2006 7:26 am
85043
Just one curious idea. Did you at some moment type F1...F8? Then Linux will promt out you another terminal view and all you type or do might appear in another...
... The only three system hangs I had in this year were allways importing some stupid text that seamed corrupted from Mircossoft-Word. There seem to be some...
Just dug out my Sherline lathe after being in storage for a while. Everything checks out right, but the Magic Smoke came out. The software, current, Vcc, Vbb...
Hello Bill, in one case a cockroach sitting on the output contacts of a 24V 10A power supply made that 300$ part smoke. So don't worry that is not so unusuall...
Hi I'm planning on building a cnc router. Instead of having expensive screw drives, could I use a timing belt drive for the three axis. How will this drive...
This has probably been out there but I haven't found it... do you have a plans / dimensions for that monitor / keyboard / start stop switch set up on pic on...
... There have been a lot of tables built with belt drives. You have a choice of a continuous belt with a drive motor on one end and an idler pulley on the...
Greetings everyone! Ballendo from the DIY-CNC pointed me over here and said I should ask you all about a "GUUT"??? I've tried a search of the archives, but...
Hi Wayne, It depends on the size of CNC, belt drive will never be like screw and as much the CNC is larger as much as the torque and precision is lower, belt...
Hi Allan, The plan contains full mechanical design of ball screw Z axis, XY axis, rail and transmission system, motor mounts. You can buy your control box or I...
Well now that the holidays are over.. time to get back to work. I've got my steppers planned out. I finally settled on a bit larger units than origianlly...
... an unregulated powersupply will run at more than the rated voltage under no load. so if the 80V is an absolute maximum limit for the geckos it will be a...
4*8 feet or inches? If feet, there are self construction sets available from shopbot. Allthough I do not like much their (in my eyes flimmsy) stuff, it is good...
