Ok, i tend to agree however, one of the guys came up with a way around it-uv led? i went to ebay and did a search, there are 41 led uv flashlights for sale all...
Where can we see them ? ... From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of Michael Noltkamper Sent: 01 April 2006...
Dave Fisher
dave@...
Apr 1, 2006 1:35 pm
86360
... around it-uv ... flashlights for ... Sorry if I sound like a negative Nancy. You are still left with a super slow gantry system and that's assuming you can...
We have some new items for building CNC routers and table based machines: #2 V-rollers Custom length, #2 V-track Flexible Dust collector brush, by the foot. ...
Hope this isn't off topic but now is the time to buy your CNC stuff before everyone's prices goes up significantly due to inflation, higher cost of raw ...
So, what else is new. The guy putting refrigerators decides that it is time to replace his car. Cars have gone up so he goes on strike and refrigerators go up....
Political discussions are off limits, off topic, and will not be allowed. bill List Mom Any arguments direct to me or _CAD_CAM_EDM_DRO-owner@yahoogroups.com_...
I am playing with both Dolphin, and Vector, for CAD/CAM, and with TurboCNC, and Mach3.. (alphabetical order) Machines are Sherline, Lathe and Mill for now. ...
I recently obtained a handful of surplus breakout "boards" that I am offering for sale. Details here: http://www.bright.net/~agarb/bkout.html Regards, Aaron...
... TurboCNC, ... Bill if you go to http://groups.yahoo.com/group/dolphincadcam/ Then Files > Post Processor Files you will find mill and lathe posts for...
has everybody had a chance to expound on his opinions? very well, now here are some facts: http://www.technology.niagarac.on.ca/people/mcsele/lasers/index.html...
In a message dated 4/1/2006 1:17:23 PM Mountain Standard Time, wanliker@... writes: and a mill post for TurbCNC Will the post for Lathe in TurboCNC be the...
... Firstly your assumption is that just because you can make a UV laser it must be suitable for stereo lithography but I doubt you have any idea if that is...
This list is for the discussion of CNC and related topics including CAD, CAM, EDM, & DRO. The list focuses on the construction of home shop CNC machines along...
CAD_CAM_EDM_DRO@yahoo...
Apr 2, 2006 3:59 am
86375
... Yeah, the Nitrogen transmission line laser is usually run at 1 - 10 Hz rep rate. It would be pretty hard to do any real assembly with only 10 pulses per ...
... market (they used to use them in direct-writing oscillographs 50 years ago) and they wouldn't be that hard to make, either. I have some little ones,...
If I actually had any motivation to do this, I believe I would just buy an argon laser that had a strong UV line, or get an argon laser and slap some UV optics...
Hi Graham and All: I have a few of these also. Only I call them white throne ideas as that is usually where there are formed. One of them goes along with...
... Since thinking about it some more I am not sure it is such a daft idea. And I think you are right about the "add-on" potential. When compared to EDM, ECM...
And if you thought ECM was only good for turbine blades have a look at these pictures: http://www.ugatu.ac.ru/ecm/detali_eng.html I'm really impressed, it...
vinyl plastisol is cheap and only takes heat to cure. might be a fun way to spend an hour playing... dunno about polymer coated sand- one expects it should not...
Hi Rick and All: The sand acts as a filler with the plastic as a binder. This way you have to cure only about a third or forth or even less of the plastic....
Hi, very interesting, i wunder if one were to add weight to the tool and use hydraulic pressure to adjust the gap spacing with the fluid? Just a quick thought...
